Menu Holden Logo

holden.wiki
Home Main Menu
Home Main Menu
  • MODEL SELECTION INDEX
  • VT SERIES I - COMMODORE, CALAIS SERVICE INFORMATION
  • SECTION 12C - INSTRUMENTS, WIPERS/WASHERS & HORN
    • 1. GENERAL DESCRIPTION
      • 1.1 INSTRUMENT FACIA SWITCHES
      • 1.2 WIPERS AND WASHERS
      • 1.3 HORN
      • 1.4 TRIP COMPUTER - SINGLE WINDOW TYPE
        • OPERATION
        • BASIC FUNCTIONS
        • ADDITIONAL FUNCTIONS
        • ADDITIONAL DISPLAYS
      • 1.5 TRIP COMPUTER - TRIPLE WINDOW TYPE
        • OPERATION
        • BASIC FUNCTIONS
        • ADDITIONAL FUNCTIONS
    • 2. INSTRUMENT SERVICE OPERATIONS
      • 2.1 INSTRUMENT CLUSTER
        • REMOVE
        • REINSTALL
        • DISASSEMBLE
        • REASSEMBLE
      • 2.2 INSTRUMENT CLUSTER INPUTS
        • CHECK
      • 2.3 SENDER UNITS
        • VEHICLE SPEED SENDER
        • FUEL GAUGE SENDER UNIT
      • 2.4 TRIP COMPUTER SWITCH ASSEMBLY
        • REMOVE
        • TESTING SWITCH
        • REINSTALL
      • 2.5 INSTRUMENT PANEL AUXILIARY POWER CONNECTOR
        • REMOVE
        • REINSTALL
    • 3. WIPERS AND WASHERS SERVICE OPERATIONS
      • 3.1 FRONT WIPER ARM
        • REMOVE
        • REINSTALL
      • 3.2 REAR WIPER ARM
        • REMOVE
        • REINSTALL
      • 3.3 FRONT AND REAR WIPER BLADES
        • REMOVE
        • REINSTALL
      • 3.4 FRONT AND REAR WIPER BLADE INSERT
        • REPLACE
      • 3.5 FRONT WIPER MOTOR AND LINKAGE
        • CHECKING WIPER MOTOR WIRING
        • CHECKING WIPER MOTOR OPERATION
        • CIRCUIT DIAGRAMS
        • REMOVE
        • REINSTALL
      • 3.6 WIPER/WASHER SWITCH
        • REMOVE
        • TESTING SWITCH
        • REINSTALL
      • 3.7 WINDSHIELD WASHERS
        • REMOVE AND REINSTALL
        • CHECKING WASHER PUMP AND WIRING
      • 3.8 REAR WIPER MOTOR
        • REMOVE
        • REINSTALL
        • CHECKING WIPER MOTOR WIRING
        • CHECKING WIPER MOTOR OPERATION
        • CIRCUIT DIAGRAMS
      • 3.9 TAILGATE WASHERS
        • REMOVE AND REINSTALL
        • CHECKING WASHER PUMP AND WIRING
    • 4. HORN SERVICE OPERATIONS
      • 4.1 HORN ASSEMBLY
        • REMOVE
        • REINSTALL
        • TEST
        • HORN RELAY
        • HORN ACTUATOR
      • 4.2 THEFT DETERRENT HORN
        • REMOVE
        • REINSTALL
        • TEST
        • THEFT DETERRENT HORN RELAY
    • 5. INSTRUMENT ASSEMBLY DIAGNOSTICS
      • 5.1 BASIC KNOWLEDGE REQUIRED
      • 5.2 PRELIMINARY SYSTEM DIAGNOSIS
      • 5.3 INSTRUMENT CLUSTER DIAGNOSTICS
        • TECH 2 DIAGNOSTIC TOOL USE WITH INTERMITTENCE
      • 5.4 DIAGNOSING FAULTS NOT COVERED BY TECH 2 DIAGNOSTIC TOOL
      • 5.5 SERIAL DATA COMMUNICATION
        • GENERAL INFORMATION
      • 5.6 CONNECTING TECH 2 FOR SYSTEM DIAGNOSIS
      • 5.7 TECH 2 TEST MODES AND DISPLAYS FOR INSTRUMENT DIAGNOSIS
        • MODEL SELECTION INDEX
        • VEHICLE IDENTIFICATION MENU
        • SYSTEM SELECTION MENU
        • VEHICLE IDENTIFICATION MENU
        • SYSTEM IDENTIFICATION MENU
        • BODY MENU
      • 5.8 INSTRUMENT DIAGNOSTICS
        • DIAGNOSTIC CIRCUIT CHECK
        • NO SERIAL DATA COMMUNICATION
        • DTC 1 FUEL GAUGE SENDER UNIT- SHORT CIRCUIT:
        • DTC 2 FUEL GAUGE SENDER UNIT - INTERMITTENT
        • DTC 3 FUEL SENDER - OPEN CIRCUIT
        • DTC 4 LPG GAUGE SENDER UNIT - OPEN CIRCUIT
        • DTC 5 LPG GAUGE SENDER UNIT - SHORT CIRCUIT
        • DTC 6 LPG GAUGE SENDER UNIT - INTERMITTENT
        • DTC - 8 NO SERIAL DATA FROM ABS
        • DTC - 9 NO SERIAL DATA FROM BCM
        • DTC - 10 NO SERIAL DATA FROM ECC
        • DTC - 11 NO SERIAL DATA FROM PCM
        • DTC - 12 NO SERIAL DATA FROM SDM
        • DTC - 13 NO INSTRUMENT POLL FROM BCM
        • DTC - 14 NO SERIAL COMMUNICATION
        • DTC - 16 ABS OR ABS/ETC FAULT LOGGED
        • DTC - 17 BCM FAULT LOGGED
        • DTC - 18 ECC FAULT LOGGED
        • DTC - 19 PCM FAULT LOGGED
        • DTC - 20 SDM FAULT LOGGED
        • DTC - 24 EE CHECKSUM = FAILURE
        • DTC - 25 ROM CHECKSUM = FAILURE
        • DTC - 26 INTERNAL FAULT
        • LOW SERIES TRIP COMPUTER DIAGNOSTIC FUNCTIONS - SINGLE WINDOW DISPLAY
        • HIGH SERIES TRIP COMPUTER DIAGNOSTIC FUNCTIONS - THREE WINDOW DISPLAY
      • 5.9 USING TECH 2 TO DIAGNOSE THE INSTRUMENT ASSEMBLY
      • 5.10 F0: NORMAL MODE
      • 5.11 F1: DIAGNOSTIC TROUBLE CODES
      • 5.12 F2: DATA DISPLAY
      • 5.13 F3: SNAPSHOT
      • 5.14 F4: MISCELLANEOUS TESTS
      • 5.15 F5: PROGRAM
    • 6. TORQUE WRENCH SPECIFICATIONS
    • 7. SPECIAL TOOLS
Made by Mibble ♥